Change oil
The change of oil is of course the first place. Regardless of whether you are a 50cc or a big trade liter, you have to change the oil to talk about the precautions.
As long as the oil you use is genuine, there is no big problem. Some people ask whether it is best to use the original engine oil. The problem is that the benevolent sees the wise and sees wisdom. Some original engine oil is filled with other brands, or As long as the oil can be guaranteed to be genuine, there is no big problem, but the price of the original engine oil is generally high (I don’t know if the manufacturer will ask me to drink tea), just look at my choice.
It is said that we are going to change the oil. It is recommended to ride the car for three or four kilometers before the oil is drained, or to idle the machine for a few minutes to warm the oil, so that the liquidity is better and the waste oil is more smooth.
Unscrew the oil dipstick of the filling machine oil port, and then find the oil draining screw of your car. Place the container for the waste oil underneath and slowly open the oil screw (it is recommended to use a socket wrench, otherwise it is easy to slide the wire), don’t be too Anxiously unscrew the whole screw, be careful to release the oil screw, seal rubber ring, spring and some simple filter of some cars, do not fall into the waste oil container, remove it and wipe it clean, wait for the waste oil to stay clean, then follow In the previous installation sequence, put the oil drain screw and other things back.
Remember to avoid waste oil, put it in the bottle and give it to the surrounding car repair, or not pollute, this time the oil discharge work has been completed, you can add new oil, once again confirm that the oil drain screw is screwed It is ok to add new oil to the filling port. If you want to add instructions to the manual or add the oil port, you can't be sure to ask the rider or dealer. Finally, check the oil dipstick or the observation window to see if the oil is in check. In the marking line.
Some vehicles may have an organic oil filter. It can filter out a lot of impurities generated during engine operation. This also needs to be replaced when the service life is reached. Some cars are replaced with two oils. Some The car will be replaced every time, this depends on the instructions and the manufacturer's advice.
The machine filter is divided into two kinds of machine filters, one is the external machine filter, and the other is the built-in machine filter. The replacement machine filter will need to add more oil than if it is not replaced. This depends on the manual.
Installation sequence: screw the oil screw to drain the oil - replace the filter - screw the oil drain screw - add new oil
External machine filter is generally more difficult to screw down, you need to use special tools, when you replace the new machine filter, remember to apply a new layer of oil on the new filter ring, so that the installation is better. The built-in machine filter finds the side cover of the filter position, and can be opened and replaced. Note that the side with the hole inward without the hole is outward.
Air filter
The air filter is equivalent to the human lung. It can help you filter out a lot of dust and impurities. It is not sucked into the cylinder and damaged the engine. However, many people are most likely to ignore it. It is also replaced according to the instructions, but it can also be based on The road conditions are different and replaced.
If you often have a sandy road or the surrounding riding environment is very bad, the air filter should be replaced in advance. Sometimes it feels that the rapid acceleration does not give oil. It may be that the air filter is dirty, and the air intake can not keep up. If your surrounding air is very good and the dirty place is not going, you can extend the time of air filter replacement.
The air filter of the scooter is generally in the upper part of the transmission. It can be changed by screwing a few screws. The position of the air filter of the gear is quite complicated. Some may be under the seat cushion, and some may be under the fuel tank. The difference is still more appropriate to the car dealership.
Change antifreeze
The use period of antifreeze is generally two years. It will be considered to be replaced soon after two years. Some people ask if water can be added to the water tank. Although the answer is yes, it is not recommended here. There are many impurities in the water. After the secondary heating and cooling, the impurities will adhere to the water tank and the water channel, causing blockage, and the boiling point of the water is not as good as the antifreeze. Now the antifreeze is not expensive, and it is not necessary to lick this.
When replacing the antifreeze solution, first find the position of the pump of your own car. The pump will have a water discharge port. After unscrewing, the antifreeze can be discharged. When the water flow stops, check if there is any residual antifreeze in the auxiliary water tank. If there is any After a short fire, pull out the drain screw after draining.
If you want to clean the water tank, you can pour the special cleaning agent for the water tank or the new antifreeze solution, and then wash it out at an idle speed. If you do not clean the water tank, you can unscrew the water inlet of the main water tank, top up the antifreeze, and then add the antifreeze to the vice. Between the two scale lines of the water tank, the water level of the auxiliary water tank is observed at a rapid speed, and if it is not reduced, it is done.
It is more troublesome to add the antifreeze to the water tank of the owner. You can only add the auxiliary water tank when the fire is idle. The anti-freezing liquid of the auxiliary water tank will be sucked away by the pressure main water tank, and how much can be taken up until it is no longer sucked.
HP Cone Crusher
(1) The limited crushing level can be used to produce finer products. Reduce maintenance downtime and increase the confidence of operators.
(2) Use the two-way iron passing release hydraulic cylinder to discharge the iron block, and implement the cleaning operation of the crushing chamber with large eccentricity when necessary. Dual accumulators can improve the response speed of the hydraulic system.
(3) HP series cone crusher can ensure the highest personnel safety and convenience of maintenance.
(4) The convenient disassembly and assembly of all key components from the top of the crusher, the convenient replacement of the lining plate, the one button fixed cone rotation disassembly function, the lining plate without the use of filler, and the comprehensive operation protection of the ICTM automation system all make the HP series the most reliable cone crusher.
Hp Bowl Assembly,Bowl Assembly,Energy Efficient Bowl Assembly,Energy Efficient Crusher Parts
Shenyang Ule Mining Machinery Co., Ltd , https://www.ulecrusherparts.com