I. Overview of the actual site
The customer's site is a Dangarra factory in a foreign country. The corners of the plant must be monitored because the plant is now completed. If the wiring is difficult, it takes a long time, and the efficiency is not high, it will also delay the customer's construction period. It has caused a certain degree of damage to already-built houses, so it chose to use wireless microwave for video surveillance. It reduces the troubles caused by construction wiring. The wireless microwave wireless bridge is a very convenient wireless monitoring and transmission solution. Wiring and troubles in wiring have greatly improved the efficiency of construction and brought convenience to customers.
II . On-site requirements
Surveillance cameras are distributed in various parts of the plant. The transmission distance will not exceed 1 km. The camera used is 2.1 million network HD. A total of 13 monitoring points, including a monitoring point near the monitoring center, can choose the wiring, other Optional wireless transmission.
The specific plan is divided into three areas, marked as shown in the figure, 1.2.3.4.5 is divided into one area. Because the five cameras are close to each other, one LA-5810E can be used for receiving. The front end uses LA-5839S to launch the No. 6.7. Using a LA-5810E to receive the 7.7.8.9.10.12 far from the 12th, with 2 LA-5810E to receive. The remaining area is also received with a LA-5810, the useless change Similarly, the topology diagram of the wireless network using the LA-5830S.com constitutes the wireless networking scheme diagram. A total of 13 points are transmitted using 12 wireless bridges and 4 wireless bridges are received. One of them is used for wiring. connection.
Three . On-site construction pay attention to things
1. The customer's site is 24H real-time monitoring. In order to ensure the normal monitoring of the field environment of the wireless monitoring equipment, all wireless monitoring equipment and monitoring equipment must provide stable voltage power supply.
2. The normal power supply voltage of the wireless bridge is DC 12-24V. Each wireless bridge will configure a POE and a power adapter for the customer.
3. The bridge connecting the camera and the wireless bridge also has a POE network cable, which can use CAT5E (control within 70m) or CAT6 (control within 100m).
4. Wireless monitoring belongs to the local area network. The IP address of the wireless bridge cannot conflict with the IP address of the camera.
5. The switch used in this wireless monitoring scheme should be as high as possible.
Custom Thermoforming
Thermoforming is a manufacturing process used to shape plastic sheets into various custom design products. It involves heating a plastic sheet until it becomes pliable, then using a mold or a vacuum to form it into the desired custom shape.
Thermoforming and vacuum forming are both processes used to shape plastic sheets into specific forms. However, there are some differences between the two techniques:
1. Process: In thermoforming, a plastic sheet is heated until it becomes pliable, and then it is pressed against a mold using pressure or a vacuum. Vacuum forming, on the other hand, relies solely on the use of a vacuum to draw the heated plastic sheet onto the mold.
2. Mold complexity: Thermoforming is typically used for more complex shapes and intricate molds, as it allows for greater detail and precision. Vacuum forming, on the other hand, is better suited for simpler shapes and molds that do not require as much detail.
3. Material thickness: Thermoforming is often used for thicker plastic sheets, typically ranging from 0.030 to 0.250 inches in thickness. Vacuum forming is more commonly used for thinner plastic sheets, typically ranging from 0.005 to 0.060 inches in thickness.
4. Production volume: Thermoforming is generally more suitable for high-volume production due to its faster cycle times and ability to handle larger sheets of plastic. Vacuum forming is better suited for low to medium volume production, as it has slower cycle times and is limited by the size of the vacuum forming machine.
5. Cost: Thermoforming typically requires more expensive equipment and molds, making it a more costly process compared to vacuum forming. Vacuum forming, on the other hand, is a more cost-effective option for smaller production runs or prototypes.
Overall, thermoforming is a more advanced and versatile process that offers greater precision and complexity, while vacuum forming is a simpler and more cost-effective option for less complex shapes and smaller production volumes.
Thermoforming is a versatile process that is widely used in industries such as packaging, automotive, aerospace, and medical. It offers advantages such as cost-effectiveness, quick turnaround times, and the ability to produce complex shapes with high precision.
Custom Thermoforming,Thermoforming Plastic Products,Thermoforming Process,ABS Thermoforming
Dongguan Yiyongli Industrial Co.,Ltd. , https://www.absthermoforming.com
